ARDUINO MKR WIFI 1010 Utvecklingskort

  • 449 kr

Vill du lägga till ett WiFi-gränssnitt till dina enheter? Få MKR WIFI 1010. Den kan enkelt kopplas till andra Arduino-produkter och kan konfigureras med hjälp a

Produkten är tyvärr slut i lager. :(

Artikelnummer: 438
Dela

Vill du lägga till ett WiFi-gränssnitt till dina enheter? Få MKR WIFI 1010. Den kan enkelt kopplas till andra Arduino-produkter och kan konfigureras med hjälp av Arduino-programvara - och du behöver inte vara en nätverksexpert. Detta är den senaste versionen av MKR 1000 WIFI, men med en ESP32-modul ombord gjord av U-BLOX.

The MKR WIFI 1010 is a significant improvement on the MKR 1000 WIFI. It's equipped with an ESP32 module made by U-BLOX. This board aims to speed up and simplify the prototyping of WiFi-based IoT applications thanks to the flexibility of the ESP32 module and its low power consumption.

The board is composed of three main blocks:

  • SAMD21 Cortex-M0+ 32bit Low Power ARM MCU;
  • U-BLOX NINA-W10 Series Low Power 2.4GHz IEEE® 802.11 b/g/n Wi-Fi; and
  • ECC508 Crypto Authentication. (datasheet)

The MKR WIFI 1010 includes 32-bit computational power, the usual rich set of I/O interfaces, and low power Wi-Fi with a Cryptochip for secure communication using SHA-256 encryption. Plus, it offers ease of use Arduino Software (IDE) for code development and programming. All of these features make this board the preferred choice for the emerging IoT battery-powered projects in a compact form.

Its USB port can be used to supply power (5V) to the board. It has a Li-Po charging circuit that allows the Arduino MKR WIFI 1010 to run on battery power or an external 5 volt source, charging the Li-Po battery while running on external power. Switching from one source to the other is done automatically.

Warning: Unlike most Arduino boards, the MKR WIFI 1010 runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting.

Technical specification 

MicrocontrollerSAMD21 Cortex-M0+ 32bit Low Power ARM MCU
Board Power Supply (USB/VIN)5V
Supported Battery(*)Li-Po Single Cell, 3.7V, 700mAh Minimum
Circuit Operating Voltage3.3V
Digital I/O Pins8
PWM Pins12 (0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 -or 19)
UART1
SPI1
I2C1
I2S1
ConnectivityWiFi
Analog Input Pins7 (ADC 8/10/12 bit)
Analog Output Pins1 (DAC 10 bit)
External Interrupts8 (0, 1, 4, 5, 6, 7, 8, A1 -or 16-, A2 - or 17)
DC Current per I/O Pin7 mA
Flash Memory256 KB
SRAM32 KB
EEPROMNo
Clock Speed32.768 kHz (RTC), 48 MHz
LED_BUILTIN6
Full-Speed USB Device and Embedded HostIncluded
LED_BUILTIN6
Length61.5 mm
Width25 mm
Weight32 gr.